/**
  Copyright (C) 2012-2019 by Autodesk, Inc.
  All rights reserved.

  FANUC Lathe post processor configuration.

  $Revision: 42389 6a4a31af7193559f6a15f6298351e6ece1a01e37 $
  $Date: 2019-07-17 22:43:53 $
  
  FORKID {88B77760-269E-4d46-8588-30814E7FE9A1}
*/

// 2019-08-03 by forhire - Adapted for SimcoTurn HL-320

description = "SimcoTurn HL-320";
vendor = "Fanuc";
vendorUrl = "http://www.fanuc.com";
legal = "Copyright (C) 2012-2019 by Autodesk, Inc.";
certificationLevel = 2;
minimumRevision = 40783;

longDescription = "SimcoTurn HL-320 with FANUC 0T-A Control in Mode B";

extension = "nc";
programNameIsInteger = true;
setCodePage("ascii");

capabilities = CAPABILITY_TURNING;
tolerance = spatial(0.002, MM);

minimumChordLength = spatial(0.25, MM);
minimumCircularRadius = spatial(0.01, MM);
maximumCircularRadius = spatial(1000, MM);
minimumCircularSweep = toRad(0.01);
maximumCircularSweep = toRad(180);
allowHelicalMoves = true;
allowedCircularPlanes = undefined; // allow any circular motion

// user-defined properties
properties = {
  writeMachine: false, // write machine
  preloadTool: false, // preloads next tool on tool change if any
  showSequenceNumbers: false, // show sequence numbers
  sequenceNumberStart: 10, // first sequence number
  sequenceNumberIncrement: 1, // increment for sequence numbers
  optionalStop: true, // optional stop
  o8: false, // specifies 8-digit program number
  separateWordsWithSpace: true, // specifies that the words should be separated with a white space
  useRadius: false, // specifies that arcs should be output using the radius (R word) instead of the I, J, and K words.
  maximumSpindleSpeed: 3550 , // specifies the maximum spindle speed
  type: "B", // specifies the type A, B, C
  useParametricFeed: false, // specifies that feed should be output using Q values
  showNotes: false, // specifies that operation notes should be output.
  g53HomePositionX: 0, // home position for X-axis
  g53HomePositionZ: 0, // home position for Z-axis
  useRigidTapping: "yes", // output rigid tapping block
  usePlanes: false, // output G17, G18, G19
  useWCS: false, // output G54-G59
  g76finishingPassDepthDesire: 0.001, // g76 Finishing Pass Depth
  g76NumSpringPassDesire: 1, // g76 Number of Spring Passes
  g76minCutDepth: 0.002, // g76 Min Cut Depth
  showComments: false, // Enable comments
  atcXZ: true, // ATC at XZ (UW) home
  barPullerEnable: false,
  barPullerToolNumber: 03,
  barPullerToolOffset: 03,
  barPullerStockLength: 36,
  barPullerEngagement: 0.25,
  barPullerMinimumClamp: 2.0,
  gearChange: true, // Use M11-M12 gear change
  gearLow: 50, // RPM of low range 50 to 450
  gearMed: 300, // RPM of med range 125 to 1120
  gearHigh: 750 // RPM of high range 400 to 3550
};

// user-defined property definitions
propertyDefinitions = {
  writeMachine: {title:"Write machine", description:"Output the machine settings in the header of the code.", group:0, type:"boolean"},
  preloadTool: {title:"Preload tool", description:"Preloads the next tool at a tool change (if any).", group:1, type:"boolean"},
  showSequenceNumbers: {title:"Use sequence numbers", description:"Use sequence numbers for each block of outputted code.", group:1, type:"boolean"},
  sequenceNumberStart: {title:"Start sequence number", description:"The number at which to start the sequence numbers.", group:1, type:"integer"},
  sequenceNumberIncrement: {title:"Sequence number increment", description:"The amount by which the sequence number is incremented by in each block.", group:1, type:"integer"},
  optionalStop: {title:"Optional stop", description:"Outputs optional stop code during when necessary in the code.", type:"boolean"},
  o8: {title:"8 Digit program number", description:"Specifies that an 8 digit program number is needed.", type:"boolean"},
  separateWordsWithSpace: {title:"Separate words with space", description:"Adds spaces between words if 'yes' is selected.", type:"boolean"},
  useRadius: {title:"Radius arcs", description:"If yes is selected, arcs are outputted using radius values rather than IJK.", type:"boolean"},
  maximumSpindleSpeed: {title:"Max spindle speed", description:"Defines the maximum spindle speed allowed by your machines.", type:"integer", range:[0, 999999999]},
  type: {title:"Type", description:"Specifies the type A, B or C.", type:"enum", values:["A", "B", "C"]},
  useParametricFeed:  {title:"Parametric feed", description:"Specifies the feed value that should be output using a Q value.", type:"boolean"},
  showNotes: {title:"Show notes", description:"Writes operation notes as comments in the outputted code.", type:"boolean"},
  g53HomePositionX: {title:"G53 home position X", description:"G53 X-axis home position.", type:"number"},
  g53HomePositionZ: {title:"G53 home position Z", description:"G53 Z-axis home position.", type:"number"},
  useRigidTapping: {
    title: "Use rigid tapping",
    description: "Select 'Yes' to enable, 'No' to disable, or 'Without spindle direction' to enable rigid tapping without outputting the spindle direction block.",
    type: "enum",
    values:[
      {title:"Yes", id:"yes"},
      {title:"No", id:"no"},
      {title:"Without spindle direction", id:"without"}
    ]
  },
  usePlanes: {title:"Include Planes", description:"Use G17-G19 to define planes.", type:"boolean"},
  useWCS: {title:"Use WCS", description:"Use G54-G59 WCS", type:"boolean"},
  g76finishingPassDepthDesire: {title: "G76 Finishing Pass", description:"G76 Depth of finishing pass.", group:0, type:"number"},
  g76NumSpringPassDesire: {title:"G76 number of spring passes", description:"G76 number of spring passes.", group:0, type:"number"},
  g76minCutDepth: {title:"G76 minimum cut depth", description:"G76 minimum cut depth.", group:0, type:"number"},
  showComments: {title:"Show comments", description:"Writes comments.", type:"boolean"},
  atcXZ: {title:"ATC at XZ Home", description:"Return to XZ Home prior to ATC.", group:0, type:"boolean"},
  barPullerEnable: {title:"Bar Puller Enable", description:"Adds Barpulling subprogram", group:0, type:"boolean"},
  barPullerToolNumber: {title:"Bar Puller Tool#", description:"Tool Number (and offset) to use for Bar Pulling tool", group:0, type:"integer", range:[0, 100]},
  barPullerToolOffset: {title:"Bar Puller Tool Offset#", description:"Offset Number to use for Bar Pulling tool", group:0, type:"integer", range:[0, 100]},
  barPullerStockLength: {title:"Bar Puller Stock Length", description:"Length of bar stock length in inches", group:0, type:"integer", range:[0, 10000]},
  barPullerEngagement: {title:"Bar Puller Engagement", description:"Bar puller engagement", group:0, type:"number"},
  barPullerMinimumClamp: {title:"Bar Puller Clamp Length", description:"Bar puller minimum chuck clamp length", group:0, type:"number"},
  gearChange: {title:"Gear Change", description:"Use M11-M13 gear changes", group:0, type:"boolean"},
  gearLow: {title:"Low Gear", description:"RPM of low range 50 to 450", group:0, type:"number"},
  gearMed: {title:"Med Gear", description:"RPM of low range 125 to 1120", group:0, type:"number"},
  gearHigh: {title:"High Gear", description:"RPM of high range 400 to 3550", group:0, type:"number"}
};

var permittedCommentChars = " ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789.,=_-";

var gFormat = createFormat({prefix:"G", decimals:1});
var mFormat = createFormat({prefix:"M", decimals:1});

var spatialFormat = createFormat({decimals:(unit == MM ? 3 : 4), forceDecimal:true});
var xFormat = createFormat({decimals:(unit == MM ? 3 : 4), forceDecimal:true, scale:2}); // diameter mode
var yFormat = createFormat({decimals:(unit == MM ? 3 : 4), forceDecimal:true});
var zFormat = createFormat({decimals:(unit == MM ? 3 : 4), forceDecimal:true});
var rFormat = createFormat({decimals:(unit == MM ? 3 : 4), forceDecimal:true}); // radius
var feedFormat = createFormat({decimals:(unit == MM ? 4 : 5), forceDecimal:true});
var pitchFormat = createFormat({decimals:6, forceDecimal:true});
var toolFormat = createFormat({decimals:0, width:4, zeropad:true});
var rpmFormat = createFormat({decimals:0});
var secFormat = createFormat({decimals:3, forceDecimal:true}); // seconds - range 0.001-99999.999
var milliFormat = createFormat({decimals:0}); // milliseconds // range 1-9999
var taperFormat = createFormat({decimals:1, scale:DEG});
//var peckFormat = createFormat({decimals:(unit == MM ? 3 : 4), forceDecimal:true});
//var peckFormat = createFormat({decimals:0, forceDecimal:false, trim:false, width:4, zeropad:true, scale:(unit == MM ? 1000 : 10000)});
var peckFormat = createFormat({decimals:0, forceDecimal:false, trim:false, scale:(unit == MM ? 1000 : 10000)});

var xOutput = createVariable({prefix:"X"}, xFormat);
var yOutput = createVariable({prefix:"Y"}, yFormat);
var zOutput = createVariable({prefix:"Z"}, zFormat);
var feedOutput = createVariable({prefix:"F"}, feedFormat);
var pitchOutput = createVariable({prefix:"F", force:true}, pitchFormat);
var sOutput = createVariable({prefix:"S", force:true}, rpmFormat);
var rOutput = createVariable({prefix:"R", force:true}, zFormat);

// circular output
var kOutput = createReferenceVariable({prefix:"K"}, spatialFormat);
var iOutput = createReferenceVariable({prefix:"I"}, spatialFormat); // no scaling

var g92ROutput = createVariable({prefix:"R"}, zFormat); // no scaling
var peckOutput = createVariable({prefix:"Q", force:true}, peckFormat);

var gMotionModal = createModal({}, gFormat); // modal group 1 // G0-G3, ...
var gPlaneModal = createModal({onchange:function () {gMotionModal.reset();}}, gFormat); // modal group 2 // G17-19
var gAbsIncModal = createModal({}, gFormat); // modal group 3 // G90-91 // only for B and C mode
var gFeedModeModal = createModal({}, gFormat); // modal group 5 // G98-99 / G94-95
var gSpindleModeModal = createModal({}, gFormat); // modal group 5 // G96-97
var gUnitModal = createModal({}, gFormat); // modal group 6 // G20-21
var gCycleModal = createModal({}, gFormat); // modal group 9 // G81, ...
var gRetractModal = createModal({}, gFormat); // modal group 10 // G98-99

// fixed settings
var firstFeedParameter = 500;
var gotSecondarySpindle = true;
var gotTailStock = false;

var WARNING_WORK_OFFSET = 0;

var QCTP = 0;
var TURRET = 1;
var GANG = 2;

var FRONT = -1;
var REAR = 1;

// collected state
var sequenceNumber;
var currentWorkOffset;
var optionalSection = false;
var forceSpindleSpeed = false;
var activeMovements; // do not use by default
var currentFeedId;
var toolingData;
var previousToolingData;

function getCode(code) {
  switch(code) {
  // case "PART_CATCHER_ON":
    // return mFormat.format(SPECIFY YOUR CODE HERE);
  // case "PART_CATCHER_OFF":
    // return mFormat.format(SPECIFY YOUR CODE HERE);
  // case "TAILSTOCK_ON":
    // return mFormat.format(SPECIFY YOUR CODE HERE);
  // case "TAILSTOCK_OFF":
    // return mFormat.format(SPECIFY YOUR CODE HERE);
  // case "ENGAGE_C_AXIS":
    // machineState.cAxisIsEngaged = true;
    // return cAxisEngageModal.format(UNSUPPORTED);
  // case "DISENGAGE_C_AXIS":
    // machineState.cAxisIsEngaged = false;
    // return cAxisEngageModal.format(UNSUPPORTED);
  // case "POLAR_INTERPOLATION_ON":
    // return gPolarModal.format(UNSUPPORTED);
  // case "POLAR_INTERPOLATION_OFF":
    // return gPolarModal.format(UNSUPPORTED);
  // case "STOP_LIVE_TOOL":
    // machineState.liveToolIsActive = false;
    // return mFormat.format(UNSUPPORTED);
  // case "STOP_MAIN_SPINDLE":
    // machineState.mainSpindleIsActive = false;
    // return mFormat.format(UNSUPPORTED);
  // case "STOP_SUB_SPINDLE":
    // machineState.subSpindleIsActive = false;
    // return mFormat.format(UNSUPPORTED);
  // case "START_LIVE_TOOL_CW":
    // machineState.liveToolIsActive = true;
    // return mFormat.format(UNSUPPORTED);
  // case "START_LIVE_TOOL_CCW":
    // machineState.liveToolIsActive = true;
    // return mFormat.format(UNSUPPORTED);
  case "START_MAIN_SPINDLE_CW":
    // machineState.mainSpindleIsActive = true;
    return mFormat.format(3);
  case "START_MAIN_SPINDLE_CCW":
    // machineState.mainSpindleIsActive = true;
    return mFormat.format(4);
  // case "START_SUB_SPINDLE_CW":
    // machineState.subSpindleIsActive = true;
    // return mFormat.format(UNSUPPORTED);
  // case "START_SUB_SPINDLE_CCW":
    // machineState.subSpindleIsActive = true;
    // return mFormat.format(UNSUPPORTED);
  // case "MAIN_SPINDLE_BRAKE_ON":
    // machineState.mainSpindleBrakeIsActive = true;
    // return cAxisBrakeModal.format(UNSUPPORTED);
  // case "MAIN_SPINDLE_BRAKE_OFF":
    // machineState.mainSpindleBrakeIsActive = false;
    // return cAxisBrakeModal.format(UNSUPPORTED);
  // case "SUB_SPINDLE_BRAKE_ON":
    // machineState.subSpindleBrakeIsActive = true;
    // return cAxisBrakeModal.format(UNSUPPORTED);
  // case "SUB_SPINDLE_BRAKE_OFF":
    // machineState.subSpindleBrakeIsActive = false;
    // return cAxisBrakeModal.format(UNSUPPORTED);
  case "FEED_MODE_UNIT_REV":
    return gFeedModeModal.format((properties.type == "A") ? 99 : 95);
  case "FEED_MODE_UNIT_MIN":
    return gFeedModeModal.format((properties.type == "A") ? 98 : 94);
  case "CONSTANT_SURFACE_SPEED_ON":
    return gSpindleModeModal.format(96);
  case "CONSTANT_SURFACE_SPEED_OFF":
    return gSpindleModeModal.format(97);
  // case "MAINSPINDLE_AIR_BLAST_ON":
    // return mFormat.format(UNSUPPORTED);
  // case "MAINSPINDLE_AIR_BLAST_OFF":
    // return mFormat.format(UNSUPPORTED);
  // case "SUBSPINDLE_AIR_BLAST_ON":
    // return mFormat.format(UNSUPPORTED);
  // case "SUBSPINDLE_AIR_BLAST_OFF":
    // return mFormat.format(UNSUPPORTED);
  // case "CLAMP_PRIMARY_CHUCK":
    // return mFormat.format(UNSUPPORTED);
  // case "UNCLAMP_PRIMARY_CHUCK":
    // return mFormat.format(UNSUPPORTED);
  // case "CLAMP_SECONDARY_CHUCK":
    // return mFormat.format(UNSUPPORTED);
  // case "UNCLAMP_SECONDARY_CHUCK":
    // return mFormat.format(UNSUPPORTED);
  // case "SPINDLE_SYNCHRONIZATION_ON":
    // machineState.spindleSynchronizationIsActive = true;
    // return gSynchronizedSpindleModal.format(UNSUPPORTED);
  // case "SPINDLE_SYNCHRONIZATION_OFF":
    // machineState.spindleSynchronizationIsActive = false;
    // return gSynchronizedSpindleModal.format(UNSUPPORTED);
  // case "START_CHIP_TRANSPORT":
    // return mFormat.format(UNSUPPORTED);
  // case "STOP_CHIP_TRANSPORT":
    // return mFormat.format(UNSUPPORTED);
  // case "OPEN_DOOR":
    // return mFormat.format(UNSUPPORTED);
  // case "CLOSE_DOOR":
    // return mFormat.format(UNSUPPORTED);
  case "COOLANT_FLOOD_ON":
    return mFormat.format(8);
  case "COOLANT_FLOOD_OFF":
    return mFormat.format(9);
  // case "COOLANT_AIR_ON":
    // return mFormat.format(UNSUPPORTED);
  // case "COOLANT_AIR_OFF":
    // return mFormat.format(UNSUPPORTED);
  case "COOLANT_THROUGH_TOOL_ON":
    return mFormat.format(88);
  case "COOLANT_THROUGH_TOOL_OFF":
    return mFormat.format(89);
  case "COOLANT_OFF":
    return mFormat.format(9);
  default:
    error(localize("Command " + code + " is not defined."));
    return 0;
  }
}

/**
  Writes the specified block.
*/
function writeBlock() {
  if (properties.showSequenceNumbers) {
    if (optionalSection) {
      var text = formatWords(arguments);
      if (text) {
        writeWords("/", "N" + sequenceNumber, text);
      }
    } else {
      writeWords2("N" + sequenceNumber, arguments);
    }
    sequenceNumber += properties.sequenceNumberIncrement;
  } else {
    if (optionalSection) {
      writeWords2("/", arguments);
    } else {
      writeWords(arguments);
    }
  }
}

/**
  Writes the specified optional block.
*/
function writeOptionalBlock() {
  if (properties.showSequenceNumbers) {
    var words = formatWords(arguments);
    if (words) {
      writeWords("/", "N" + sequenceNumber, words);
      sequenceNumber += properties.sequenceNumberIncrement;
    }
  } else {
    writeWords2("/", arguments);
  }
}

function formatComment(text) {
  return "(" + filterText(String(text).toUpperCase(), permittedCommentChars).replace(/[()]/g, "") + ")";
}

/**
  Output a comment.
*/
function writeComment(text) {
  if (properties.showComments) {
    writeln(formatComment(text));
  }
}

function onOpen() {
  if (properties.useRadius) {
    maximumCircularSweep = toRad(90); // avoid potential center calculation errors for CNC
  }

  yOutput.disable();

  if (!(properties.type in {"A":0, "B":0, "C":0})) {
    error(localize("Unsupported type. Only A, B, and C are allowed."));
    return;
  }
  
  if (!properties.separateWordsWithSpace) {
    setWordSeparator("");
  }

  sequenceNumber = properties.sequenceNumberStart;
  writeln("%");

  if (programName) {
    var programId;
    try {
      programId = getAsInt(programName);
    } catch(e) {
      error(localize("Program name must be a number."));
      return;
    }
    if (properties.o8) {
      if (!((programId >= 1) && (programId <= 99999999))) {
        error(localize("Program number is out of range."));
        return;
      }
    } else {
      if (!((programId >= 1) && (programId <= 9999))) {
        error(localize("Program number is out of range."));
        return;
      }
    }
    if ((programId >= 8000) && (programId <= 9999)) {
      warning(localize("Program number is reserved by tool builder."));
    }
    var oFormat = createFormat({width:(properties.o8 ? 8 : 4), zeropad:true, decimals:0});
    if (programComment) {
      writeln("O" + oFormat.format(programId) + " (" + filterText(String(programComment).toUpperCase(), permittedCommentChars) + ")");
    } else {
      writeln("O" + oFormat.format(programId));
    }
  } else {
    error(localize("Program name has not been specified."));
    return;
  }

  // dump machine configuration
  var vendor = machineConfiguration.getVendor();
  var model = machineConfiguration.getModel();
  var description = machineConfiguration.getDescription();

  if (properties.writeMachine && (vendor || model || description)) {
    writeComment(localize("Machine"));
    if (vendor) {
      writeComment("  " + localize("vendor") + ": " + vendor);
    }
    if (model) {
      writeComment("  " + localize("model") + ": " + model);
    }
    if (description) {
      writeComment("  " + localize("description") + ": "  + description);
    }
  }

  if ((getNumberOfSections() > 0) && (getSection(0).workOffset == 0)) {
    for (var i = 0; i < getNumberOfSections(); ++i) {
      if (getSection(i).workOffset > 0) {
        error(localize("Using multiple work offsets is not possible if the initial work offset is 0."));
        return;
      }
    }
  }

  // absolute coordinates and feed per min
  if (properties.type == "A") {
    writeBlock(gFeedModeModal.format(98), conditional(properties.usePlanes, gPlaneModal.format(18)));
  } else {
    writeBlock(gAbsIncModal.format(90), gFeedModeModal.format(95), conditional(properties.usePlanes, gPlaneModal.format(18)));
  }

  switch (unit) {
  case IN:
    writeBlock(gUnitModal.format(20));
    break;
  case MM:
    writeBlock(gUnitModal.format(21));
    break;
  }

  if (properties.type == "A") {
    writeBlock(gFormat.format(50), sOutput.format(properties.maximumSpindleSpeed));
  } else {
    writeBlock(gFormat.format(92), sOutput.format(properties.maximumSpindleSpeed));
  }

 if (properties.barPullerEnable) {
    var workpiece = getWorkpiece();
    var stockDiameter = (workpiece.upper.x - workpiece.lower.x);
    var stockLength = (workpiece.upper.z - workpiece.lower.z);
    var BarLength = properties.barPullerStockLength;
    var ClampLength = properties.barPullerMinimumClamp;
    var partQuantity = Math.floor((BarLength-ClampLength) / stockLength);
    writeBlock("G65 H01 P#501 Q" + partQuantity); // part qty
    writeBlock("G65 H01 P#502 Q0"); // internal var for part count
}


  onCommand(COMMAND_START_CHIP_TRANSPORT);
}

function onComment(message) {
  writeComment(message);
}

/** Force output of X, Y, and Z. */
function forceXYZ() {
  xOutput.reset();
  yOutput.reset();
  zOutput.reset();
}

function forceFeed() {
  currentFeedId = undefined;
  feedOutput.reset();
}

/** Force output of X, Y, Z, and F on next output. */
function forceAny() {
  forceXYZ();
  forceFeed();
}

function FeedContext(id, description, feed) {
  this.id = id;
  this.description = description;
  this.feed = feed;
}

function getFeed(f) {
  if (activeMovements) {
    var feedContext = activeMovements[movement];
    if (feedContext != undefined) {
      if (!feedFormat.areDifferent(feedContext.feed, f)) {
        if (feedContext.id == currentFeedId) {
          return ""; // nothing has changed
        }
        forceFeed();
        currentFeedId = feedContext.id;
        return "F#" + (firstFeedParameter + feedContext.id);
      }
    }
    currentFeedId = undefined; // force Q feed next time
  }
  return feedOutput.format(f); // use feed value
}

function initializeActiveFeeds() {
  activeMovements = new Array();
  var movements = currentSection.getMovements();
  var feedPerRev = currentSection.feedMode == FEED_PER_REVOLUTION;
  
  var id = 0;
  var activeFeeds = new Array();
  if (hasParameter("operation:tool_feedCutting")) {
    if (movements & ((1 << MOVEMENT_CUTTING) | (1 << MOVEMENT_LINK_TRANSITION) | (1 << MOVEMENT_EXTENDED))) {
      var feedContext = new FeedContext(id, localize("Cutting"), feedPerRev ? getParameter("operation:tool_feedCuttingRel") : getParameter("operation:tool_feedCutting"));
      activeFeeds.push(feedContext);
      activeMovements[MOVEMENT_CUTTING] = feedContext;
      activeMovements[MOVEMENT_LINK_TRANSITION] = feedContext;
      activeMovements[MOVEMENT_EXTENDED] = feedContext;
    }
    ++id;
    if (movements & (1 << MOVEMENT_PREDRILL)) {
      feedContext = new FeedContext(id, localize("Predrilling"), feedPerRev ? getParameter("operation:tool_feedCuttingRel") : getParameter("operation:tool_feedCutting"));
      activeMovements[MOVEMENT_PREDRILL] = feedContext;
      activeFeeds.push(feedContext);
    }
    ++id;
  }
  
  if (hasParameter("operation:finishFeedrate")) {
    if (movements & (1 << MOVEMENT_FINISH_CUTTING)) {
      var finishFeedrateRel;
      if (hasParameter("operation:finishFeedrateRel")) {
        finishFeedrateRel = getParameter("operation:finishFeedrateRel");
      } else if (hasParameter("operation:finishFeedratePerRevolution")) {
        finishFeedrateRel = getParameter("operation:finishFeedratePerRevolution");
      }
      var feedContext = new FeedContext(id, localize("Finish"), feedPerRev ? finishFeedrateRel : getParameter("operation:finishFeedrate"));
      activeFeeds.push(feedContext);
      activeMovements[MOVEMENT_FINISH_CUTTING] = feedContext;
    }
    ++id;
  } else if (hasParameter("operation:tool_feedCutting")) {
    if (movements & (1 << MOVEMENT_FINISH_CUTTING)) {
      var feedContext = new FeedContext(id, localize("Finish"), feedPerRev ? getParameter("operation:tool_feedCuttingRel") : getParameter("operation:tool_feedCutting"));
      activeFeeds.push(feedContext);
      activeMovements[MOVEMENT_FINISH_CUTTING] = feedContext;
    }
    ++id;
  }
  
  if (hasParameter("operation:tool_feedEntry")) {
    if (movements & (1 << MOVEMENT_LEAD_IN)) {
      var feedContext = new FeedContext(id, localize("Entry"), feedPerRev ? getParameter("operation:tool_feedEntryRel") : getParameter("operation:tool_feedEntry"));
      activeFeeds.push(feedContext);
      activeMovements[MOVEMENT_LEAD_IN] = feedContext;
    }
    ++id;
  }

  if (hasParameter("operation:tool_feedExit")) {
    if (movements & (1 << MOVEMENT_LEAD_OUT)) {
      var feedContext = new FeedContext(id, localize("Exit"), feedPerRev ? getParameter("operation:tool_feedExitRel") : getParameter("operation:tool_feedExit"));
      activeFeeds.push(feedContext);
      activeMovements[MOVEMENT_LEAD_OUT] = feedContext;
    }
    ++id;
  }

  if (hasParameter("operation:noEngagementFeedrate")) {
    if (movements & (1 << MOVEMENT_LINK_DIRECT)) {
      var feedContext = new FeedContext(id, localize("Direct"), feedPerRev ? getParameter("operation:noEngagementFeedrateRel") : getParameter("operation:noEngagementFeedrate"));
      activeFeeds.push(feedContext);
      activeMovements[MOVEMENT_LINK_DIRECT] = feedContext;
    }
    ++id;
  } else if (hasParameter("operation:tool_feedCutting") &&
             hasParameter("operation:tool_feedEntry") &&
             hasParameter("operation:tool_feedExit")) {
    if (movements & (1 << MOVEMENT_LINK_DIRECT)) {
      var feedContext = new FeedContext(
        id,
        localize("Direct"),
        Math.max(
          feedPerRev ? getParameter("operation:tool_feedCuttingRel") : getParameter("operation:tool_feedCutting"),
          feedPerRev ? getParameter("operation:tool_feedEntryRel") : getParameter("operation:tool_feedEntry"),
          feedPerRev ? getParameter("operation:tool_feedExitRel") : getParameter("operation:tool_feedExit")
        )
      );
      activeFeeds.push(feedContext);
      activeMovements[MOVEMENT_LINK_DIRECT] = feedContext;
    }
    ++id;
  }
  
  if (hasParameter("operation:reducedFeedrate")) {
    if (movements & (1 << MOVEMENT_REDUCED)) {
      var feedContext = new FeedContext(id, localize("Reduced"), feedPerRev ? getParameter("operation:reducedFeedrateRel") : getParameter("operation:reducedFeedrate"));
      activeFeeds.push(feedContext);
      activeMovements[MOVEMENT_REDUCED] = feedContext;
    }
    ++id;
  }

  if (hasParameter("operation:tool_feedRamp")) {
    if (movements & ((1 << MOVEMENT_RAMP) | (1 << MOVEMENT_RAMP_HELIX) | (1 << MOVEMENT_RAMP_PROFILE) | (1 << MOVEMENT_RAMP_ZIG_ZAG))) {
      var feedContext = new FeedContext(id, localize("Ramping"), feedPerRev ? getParameter("operation:tool_feedRampRel") : getParameter("operation:tool_feedRamp"));
      activeFeeds.push(feedContext);
      activeMovements[MOVEMENT_RAMP] = feedContext;
      activeMovements[MOVEMENT_RAMP_HELIX] = feedContext;
      activeMovements[MOVEMENT_RAMP_PROFILE] = feedContext;
      activeMovements[MOVEMENT_RAMP_ZIG_ZAG] = feedContext;
    }
    ++id;
  }
  if (hasParameter("operation:tool_feedPlunge")) {
    if (movements & (1 << MOVEMENT_PLUNGE)) {
      var feedContext = new FeedContext(id, localize("Plunge"), feedPerRev ? getParameter("operation:tool_feedPlungeRel") : getParameter("operation:tool_feedPlunge"));
      activeFeeds.push(feedContext);
      activeMovements[MOVEMENT_PLUNGE] = feedContext;
    }
    ++id;
  }
  if (true) { // high feed
    if (movements & (1 << MOVEMENT_HIGH_FEED)) {
      var feedContext = new FeedContext(id, localize("High Feed"), this.highFeedrate);
      activeFeeds.push(feedContext);
      activeMovements[MOVEMENT_HIGH_FEED] = feedContext;
    }
    ++id;
  }
  
  for (var i = 0; i < activeFeeds.length; ++i) {
    var feedContext = activeFeeds[i];
    writeBlock("#" + (firstFeedParameter + feedContext.id) + "=" + feedFormat.format(feedContext.feed), formatComment(feedContext.description));
  }
}

function getSpindle() {
  if (getNumberOfSections() == 0) {
    return SPINDLE_PRIMARY;
  }
  if (getCurrentSectionId() < 0) {
    return getSection(getNumberOfSections() - 1).spindle == 0;
  }
  if (currentSection.getType() == TYPE_TURNING) {
    return currentSection.spindle;
  } else {
    if (isSameDirection(currentSection.workPlane.forward, new Vector(0, 0, 1))) {
      return SPINDLE_PRIMARY;
    } else if (isSameDirection(currentSection.workPlane.forward, new Vector(0, 0, -1))) {
      if (!gotSecondarySpindle) {
        error(localize("Secondary spindle is not available."));
      }
      return SPINDLE_SECONDARY;
    } else {
      return SPINDLE_PRIMARY;
    }
  }
}

function ToolingData(_tool) {
  switch (_tool.turret) {
  // Positional Turret
  case 0:
    this.tooling = TURRET;
    this.toolPost = REAR;
    break;
  // QCTP X-
  case 101:
    this.tooling = QCTP;
    this.toolPost = FRONT;
    break;
  // QCTP X+
  case 102:
    this.tooling = QCTP;
    this.toolPost = REAR;
    break;
  // Gang Tooling X-
  case 103:
    this.tooling = GANG;
    this.toolPost = FRONT;
    break;
  // Gang Tooling X+
  case 104:
    this.tooling = GANG;
    this.toolPost = REAR;
    break;
  default:
    error(localize("Turret number must be 0 (main turret), 101 (QCTP X-), 102 (QCTP X+, 103 (gang tooling X-), or 104 (gang tooling X+)."));
    break;
  }
  this.number = _tool.number;
  this.comment = _tool.comment;
  this.toolLength = _tool.bodyLength;
  // HSMWorks returns 0 in tool.bodyLength
  if ((tool.bodyLength == 0) && hasParameter("operation:tool_bodyLength")) {
    this.toolLength = getParameter("operation:tool_bodyLength");
  }
}

function onSection() {
  if (currentSection.getType() != TYPE_TURNING) {
    if (!hasParameter("operation-strategy") || (getParameter("operation-strategy") != "drill")) {
      if (currentSection.getType() == TYPE_MILLING) {
        error(localize("Milling toolpath is not supported."));
      } else {
        error(localize("Non-turning toolpath is not supported."));
      }
      return;
    }
  }

  var forceToolAndRetract = optionalSection && !currentSection.isOptional();
  optionalSection = currentSection.isOptional();

  var turning = (currentSection.getType() == TYPE_TURNING);
  
  var insertToolCall = forceToolAndRetract || isFirstSection() ||
    currentSection.getForceToolChange && currentSection.getForceToolChange() ||
    (tool.number != getPreviousSection().getTool().number) ||
    (tool.compensationOffset != getPreviousSection().getTool().compensationOffset) ||
    (tool.diameterOffset != getPreviousSection().getTool().diameterOffset) ||
    (tool.lengthOffset != getPreviousSection().getTool().lengthOffset);
  
  var retracted = false; // specifies that the tool has been retracted to the safe plane
  var newSpindle = isFirstSection() ||
    (getPreviousSection().spindle != currentSection.spindle);
  var newWorkOffset = isFirstSection() ||
    (getPreviousSection().workOffset != currentSection.workOffset); // work offset changes
  
  // determine which tooling holder is used
  if (!isFirstSection()) {
    previousToolingData = toolingData;
  }
  toolingData = new ToolingData(tool);
  toolingData.operationComment = "";
  if (hasParameter("operation-comment")) {
    toolingData.operationComment = getParameter("operation-comment");
  }
  toolingData.toolChange = insertToolCall;
  if (isFirstSection()) {
    previousToolingData = toolingData;
  }

  // turning using front tool post
  if (toolingData.toolPost == FRONT) {
    xFormat = createFormat({decimals:(unit == MM ? 3 : 4), forceDecimal:true, scale:-2});
    xOutput = createVariable({prefix:"X"}, xFormat);
    iFormat = createFormat({decimals:(unit == MM ? 3 : 4), forceDecimal:true, scale:-1}); // radius mode
    iOutput = createReferenceVariable({prefix:"I"}, iFormat);

  // turning using rear tool post
  } else {
    xFormat = createFormat({decimals:(unit == MM ? 3 : 4), forceDecimal:true, scale:2});
    xOutput = createVariable({prefix:"X"}, xFormat);
    iFormat = createFormat({decimals:(unit == MM ? 3 : 4), forceDecimal:true, scale:1}); // radius mode
    iOutput = createReferenceVariable({prefix:"I"}, iFormat);
  }

  if (insertToolCall || newSpindle || newWorkOffset) {
    // retract to safe plane
    retracted = true;
    if (!isFirstSection() && insertToolCall) {
      onCommand(COMMAND_COOLANT_OFF);
    }
    if (properties.atcXZ) {
       writeBlock(gFormat.format(28), "U" + xFormat.format(0), "W" + zFormat.format(0)); // retract
    } else {
       writeBlock(gFormat.format(28), "U" + xFormat.format(0)); // retract
    }
    forceXYZ();
  }

  writeln("");

  if (hasParameter("operation-comment")) {
    var comment = getParameter("operation-comment");
    if (comment) {
      writeComment(comment);
    }
  }
  
  if (properties.showNotes && hasParameter("notes")) {
    var notes = getParameter("notes");
    if (notes) {
      var lines = String(notes).split("\n");
      var r1 = new RegExp("^[\\s]+", "g");
      var r2 = new RegExp("[\\s]+$", "g");
      for (line in lines) {
        var comment = lines[line].replace(r1, "").replace(r2, "");
        if (comment) {
          writeComment(comment);
        }
      }
    }
  }
  
  if (insertToolCall) {
    retracted = true;
    // onCommand(COMMAND_COOLANT_OFF);
  
    if (!isFirstSection() && properties.optionalStop) {
      onCommand(COMMAND_OPTIONAL_STOP);
    }

    if (tool.number > 99) {
      warning(localize("Tool number exceeds maximum value."));
    }

    if ((toolingData.tooling == QCTP) || tool.getManualToolChange()) {
      var comment = formatComment(localize("CHANGE TO T") + tool.number + " " + localize("ON") + " " +
        localize((toolingData.toolPost == REAR) ? "REAR TOOL POST" : "FRONT TOOL POST"));
      writeBlock(mFormat.format(0), comment);
    }

    var compensationOffset = tool.isTurningTool() ? tool.compensationOffset : tool.lengthOffset;
    if (compensationOffset > 99) {
      error(localize("Compensation offset is out of range."));
      return;
    }

   if (properties.barPullerEnable && isFirstSection()) {
      writeBlock("N01M1");
    } 

    writeBlock("T" + toolFormat.format(tool.number * 100 + compensationOffset));
    if (tool.comment) {
      writeComment(tool.comment);
    }

    if (properties.preloadTool) {
      var nextTool = getNextTool(tool.number);
      if (nextTool) {
        var compensationOffset = nextTool.isTurningTool() ? nextTool.compensationOffset : nextTool.lengthOffset;
        if (compensationOffset > 99) {
          error(localize("Compensation offset is out of range."));
          return;
        }
        writeBlock("T" + toolFormat.format(nextTool.number * 100 + compensationOffset));
      } else {
        // preload first tool
        var section = getSection(0);
        var firstTool = section.getTool().number;
        if (tool.number != firstTool.number) {
          var compensationOffset = firstTool.isTurningTool() ? firstTool.compensationOffset : firstTool.lengthOffset;
          if (compensationOffset > 99) {
            error(localize("Compensation offset is out of range."));
            return;
          }
          writeBlock("T" + toolFormat.format(firstTool.number * 100 + compensationOffset));
        }
      }
    }
  }

  // wcs
  if (properties.useWCS) {
  if (insertToolCall) { // force work offset when changing tool
    currentWorkOffset = undefined;
  }
  var workOffset = currentSection.workOffset;
  if (workOffset == 0) {
    warningOnce(localize("Work offset has not been specified. Using G54 as WCS."), WARNING_WORK_OFFSET);
    workOffset = 1;
  }
  if (workOffset > 0) {
    if (workOffset > 6) {
      var p = workOffset - 6; // 1->...
      if (p > 300) {
        error(localize("Work offset out of range."));
        return;
      } else {
        if (workOffset != currentWorkOffset) {
          writeBlock(gFormat.format(54.1), "P" + p); // G54.1P
          currentWorkOffset = workOffset;
        }
      }
    } else {
      if (workOffset != currentWorkOffset) {
        writeBlock(gFormat.format(53 + workOffset)); // G54->G59
        currentWorkOffset = workOffset;
      }
    }
  }
  }

  // set coolant after we have positioned at Z
  setCoolant(tool.coolant);

  forceAny();
  gMotionModal.reset();

  gFeedModeModal.reset();
  if (currentSection.feedMode == FEED_PER_REVOLUTION) {
    writeBlock(getCode("FEED_MODE_UNIT_REV"));
  } else {
    writeBlock(getCode("FEED_MODE_UNIT_MIN"));
  }

  if (gotTailStock) {
    writeBlock(currentSection.tailstock ? getCode("TAILSTOCK_ON") : getCode("TAILSTOCK_OFF"));
  }
  // writeBlock(mFormat.format(clampPrimaryChuck ? x : x));
  // writeBlock(mFormat.format(clampSecondaryChuck ? x : x));
  
  var tapping = hasParameter("operation:cycleType") &&
    ((getParameter("operation:cycleType") == "tapping") ||
    (getParameter("operation:cycleType") == "right-tapping") ||
    (getParameter("operation:cycleType") == "left-tapping") ||
    (getParameter("operation:cycleType") == "tapping-with-chip-breaking"));
  var initialPosition = getFramePosition(currentSection.getInitialPosition());
  if (!tapping || (tapping && !(properties.useRigidTapping == "without"))) {
    startSpindle(false, true, initialPosition);
  }
  
  setRotation(currentSection.workPlane);

  if (currentSection.partCatcher) {
    engagePartCatcher(true);
  }

  if (!retracted) {
    // TAG: need to retract along X or Z
    if (getCurrentPosition().z < initialPosition.z) {
      writeBlock(gMotionModal.format(0), zOutput.format(initialPosition.z));
    }
  }

  if (insertToolCall || tool.getSpindleMode() == SPINDLE_CONSTANT_SURFACE_SPEED) {
    gMotionModal.reset();
    
    if (properties.type == "A") {
      writeBlock(
        gMotionModal.format(0), xOutput.format(initialPosition.x), yOutput.format(initialPosition.y), zOutput.format(initialPosition.z)
      );
    } else {
      writeBlock(
        gAbsIncModal.format(90),
        gMotionModal.format(0), xOutput.format(initialPosition.x), yOutput.format(initialPosition.y), zOutput.format(initialPosition.z)
      );
    }

    gMotionModal.reset();
  }

  // enable SFM spindle speed
  if (tool.getSpindleMode() == SPINDLE_CONSTANT_SURFACE_SPEED) {
    startSpindle(false, false);
  }

  if (properties.useParametricFeed &&
      hasParameter("operation-strategy") &&
      (getParameter("operation-strategy") != "drill") && // legacy
      !(currentSection.hasAnyCycle && currentSection.hasAnyCycle())) {
    if (!insertToolCall &&
        activeMovements &&
        (getCurrentSectionId() > 0) &&
        ((getPreviousSection().getPatternId() == currentSection.getPatternId()) && (currentSection.getPatternId() != 0))) {
      // use the current feeds
    } else {
      initializeActiveFeeds();
    }
  } else {
    activeMovements = undefined;
  }

  if (insertToolCall || retracted) {
    gPlaneModal.reset();
  }
}

function onDwell(seconds) {
  if (seconds > 99999.999) {
    warning(localize("Dwelling time is out of range."));
  }
  milliseconds = clamp(1, seconds * 1000, 99999999);
  writeBlock(/*gFeedModeModal.format(94),*/ gFormat.format(4), "P" + milliFormat.format(milliseconds));
}

var pendingRadiusCompensation = -1;

function onRadiusCompensation() {
  pendingRadiusCompensation = radiusCompensation;
}

function onRapid(_x, _y, _z) {
  var x = xOutput.format(_x);
  var y = yOutput.format(_y);
  var z = zOutput.format(_z);
  if (x || y || z) {
    if (pendingRadiusCompensation >= 0) {
      pendingRadiusCompensation = -1;
      switch (radiusCompensation) {
      case RADIUS_COMPENSATION_LEFT:
        writeBlock(gMotionModal.format(0), gFormat.format(41), x, y, z);
        break;
      case RADIUS_COMPENSATION_RIGHT:
        writeBlock(gMotionModal.format(0), gFormat.format(42), x, y, z);
        break;
      default:
        writeBlock(gMotionModal.format(0), gFormat.format(40), x, y, z);
      }
    } else {
      writeBlock(gMotionModal.format(0), x, y, z);
    }
    forceFeed();
  }
}

var resetFeed = false;

function onLinear(_x, _y, _z, feed) {
  if (isSpeedFeedSynchronizationActive()) {
    resetFeed = true;
    var threadPitch = getParameter("operation:threadPitch");
    var threadsPerInch = 1.0/threadPitch; // per mm for metric
    writeBlock(gMotionModal.format(32), xOutput.format(_x), yOutput.format(_y), zOutput.format(_z), pitchOutput.format(1/threadsPerInch));
    return;
  }
  if (resetFeed) {
    resetFeed = false;
    forceFeed();
  }
  var x = xOutput.format(_x);
  var y = yOutput.format(_y);
  var z = zOutput.format(_z);
  var f = getFeed(feed);
  if (x || y || z) {
    if (pendingRadiusCompensation >= 0) {
      pendingRadiusCompensation = -1;
      writeBlock(conditional(properties.usePlanes, gPlaneModal.format(18)));
      switch (radiusCompensation) {
      case RADIUS_COMPENSATION_LEFT:
        writeBlock(gMotionModal.format(isSpeedFeedSynchronizationActive() ? 32 : 1), gFormat.format(41), x, y, z, f);
        break;
      case RADIUS_COMPENSATION_RIGHT:
        writeBlock(gMotionModal.format(isSpeedFeedSynchronizationActive() ? 32 : 1), gFormat.format(42), x, y, z, f);
        break;
      default:
        writeBlock(gMotionModal.format(isSpeedFeedSynchronizationActive() ? 32 : 1), gFormat.format(40), x, y, z, f);
      }
    } else {
      writeBlock(gMotionModal.format(isSpeedFeedSynchronizationActive() ? 32 : 1), x, y, z, f);
    }
  } else if (f) {
    if (getNextRecord().isMotion()) { // try not to output feed without motion
      forceFeed(); // force feed on next line
    } else {
      writeBlock(gMotionModal.format(isSpeedFeedSynchronizationActive() ? 32 : 1), f);
    }
  }
}

function onCircular(clockwise, cx, cy, cz, x, y, z, feed) {
  if (isSpeedFeedSynchronizationActive()) {
    error(localize("Speed-feed synchronization is not supported for circular moves."));
    return;
  }
  
  if (pendingRadiusCompensation >= 0) {
    error(localize("Radius compensation cannot be activated/deactivated for a circular move."));
    return;
  }

  var start = getCurrentPosition();
  var directionCode = (toolingData.toolPost == REAR) ? (clockwise ? 2 : 3) : (clockwise ? 3 : 2);

  if (isFullCircle()) {
    if (properties.useRadius || isHelical()) { // radius mode does not support full arcs
      linearize(tolerance);
      return;
    }
    switch (getCircularPlane()) {
    case PLANE_XY:
      writeBlock(conditional(properties.type != "A", gAbsIncModal.format(90)), conditional(properties.usePlanes, gPlaneModal.format(17)), gMotionModal.format(directionCode), iOutput.format(cx - start.x, 0), jOutput.format(cy - start.y, 0), getFeed(feed));
      break;
    case PLANE_ZX:
      writeBlock(conditional(properties.type != "A", gAbsIncModal.format(90)), conditional(properties.usePlanes, gPlaneModal.format(18)), gMotionModal.format(directionCode), iOutput.format(cx - start.x, 0), kOutput.format(cz - start.z, 0), getFeed(feed));
      break;
    case PLANE_YZ:
      writeBlock(conditional(properties.type != "A", gAbsIncModal.format(90)), conditional(properties.usePlanes, gPlaneModal.format(19)), gMotionModal.format(directionCode), jOutput.format(cy - start.y, 0), kOutput.format(cz - start.z, 0), getFeed(feed));
      break;
    default:
      linearize(tolerance);
    }
  } else if (!properties.useRadius) {
    switch (getCircularPlane()) {
    case PLANE_XY:
      writeBlock(conditional(properties.type != "A", gAbsIncModal.format(90)), conditional(properties.usePlanes, gPlaneModal.format(17)), gMotionModal.format(directionCode), xOutput.format(x), yOutput.format(y), zOutput.format(z), iOutput.format(cx - start.x, 0), jOutput.format(cy - start.y, 0), getFeed(feed));
      break;
    case PLANE_ZX:
      writeBlock(conditional(properties.type != "A", gAbsIncModal.format(90)), conditional(properties.usePlanes, gPlaneModal.format(18)), gMotionModal.format(directionCode), xOutput.format(x), yOutput.format(y), zOutput.format(z), iOutput.format(cx - start.x, 0), kOutput.format(cz - start.z, 0), getFeed(feed));
      break;
    case PLANE_YZ:
      writeBlock(conditional(properties.type != "A", gAbsIncModal.format(90)), conditional(properties.usePlanes, gPlaneModal.format(19)), gMotionModal.format(directionCode), xOutput.format(x), yOutput.format(y), zOutput.format(z), jOutput.format(cy - start.y, 0), kOutput.format(cz - start.z, 0), getFeed(feed));
      break;
    default:
      linearize(tolerance);
    }
  } else { // use radius mode
    var r = getCircularRadius();
    if (toDeg(getCircularSweep()) > (180 + 1e-9)) {
      r = -r; // allow up to <360 deg arcs
    }
    switch (getCircularPlane()) {
    case PLANE_XY:
      writeBlock(conditional(properties.usePlanes, gPlaneModal.format(17)), gMotionModal.format(directionCode), xOutput.format(x), yOutput.format(y), zOutput.format(z), "R" + rFormat.format(r), getFeed(feed));
      break;
    case PLANE_ZX:
      writeBlock(conditional(properties.usePlanes, gPlaneModal.format(18)), gMotionModal.format(directionCode), xOutput.format(x), yOutput.format(y), zOutput.format(z), "R" + rFormat.format(r), getFeed(feed));
      break;
    case PLANE_YZ:
      writeBlock(conditional(properties.usePlanes, gPlaneModal.format(19)), gMotionModal.format(directionCode), xOutput.format(x), yOutput.format(y), zOutput.format(z), "R" + rFormat.format(r), getFeed(feed));
      break;
    default:
      linearize(tolerance);
    }
  }
}

function onCycle() {
}

function getCommonCycle(x, y, z, r) {
  forceXYZ(); // force xyz on first drill hole of any cycle
  return [xOutput.format(x), yOutput.format(y),
    zOutput.format(z),
    "R" + spatialFormat.format(r)];
}

function getCurrentCycle(x, y, z) {
  forceXYZ(); // force xyz on first drill hole of any cycle
  return [xOutput.format(x), yOutput.format(y),
    zOutput.format(z)];
}

function onCyclePoint(x, y, z) {
  if (isSameDirection(currentSection.workPlane.forward, new Vector(0, 0, 1)) ||
      isSameDirection(currentSection.workPlane.forward, new Vector(0, 0, -1))) {
    if (properties.usePlanes) {gPlaneModal.format(17)}; // 2-axis lathes typically don't use G17
  } else {
    expandCyclePoint(x, y, z);
    return;
  }

/*
  switch (cycleType) {
  case "thread-turning":
    var inverted = (toolingData.toolPost == REAR) ? 1 : -1;
    var r = -cycle.incrementalX * inverted; // positive if taper goes down - delta radius
    var threadsPerInch = 1.0/cycle.pitch; // per mm for metric
    var f = 1/threadsPerInch;
    var codes = {A: 92, B: 78, C: 21};
    writeBlock(
      gMotionModal.format(codes[properties.type]),
      xOutput.format(x - cycle.incrementalX),
      yOutput.format(y),
      zOutput.format(z),
      conditional(zFormat.isSignificant(r), g92ROutput.format(r)),
      feedOutput.format(f)
    );
    return;
  }
*/

if (isLastCyclePoint()) {
var schrijven = true;
}
  switch (cycleType) {

   case "thread-turning":
      var internal = (getParameter("operation:tool_internalThread") == 1) ? -1 : 1;
      var threadDepth = secFormat.format(getParameter("operation:threadDepth"))*10000;
      var firstCutDepth = Math.round(threadDepth/Math.sqrt(getParameter("operation:numberOfStepdowns"))); 
      var cuttingFeedrate = feedOutput.format(getParameter("movement:cutting"));
      if(schrijven == true){
        /* Pxxyyzz   xx- number of spring, yy- chamfer amount to pull, zz-thread angle*/
         writeBlock(
        (properties.type == "A") ? "" : gRetractModal.format(98), conditional(properties.type != "A", gAbsIncModal.format(90)), gCycleModal.format(76),
                "P0" + getParameter("operation:nullPass")*properties.g76NumSpringPassDesire+ "00" + getParameter("operation:infeedAngle")*2,
                "Q" + properties.g76minCutDepth*10000,
          	"R" + properties.g76finishingPassDepthDesire
                  );
        gMotionModal.reset();

                xOutput.reset(); // at least one axis is required
                zOutput.reset();
                feedOutput.reset();
      writeBlock(
          gFormat.format(76),
                xOutput.format(x),
                zOutput.format(z),
                "R" + rFormat.format(cycle.incrementalX*internal),
                "P" + threadDepth, // not optional
                "Q" + firstCutDepth, 
                feedOutput.format(getParameter("operation:threadPitch"))
     );

         writeBlock(gCycleModal.format(80));}
         schrijven = false;

      return;}

  if (isFirstCyclePoint()) {
    repositionToCycleClearance(cycle, x, y, z);

    var F = cycle.feedrate;
    var P = !cycle.dwell ? 0 : clamp(1, cycle.dwell * 1000, 99999999); // in milliseconds

    switch (cycleType) {
    case "drilling":
      writeBlock(
        (properties.type == "A") ? "" : gRetractModal.format(98), conditional(properties.type != "A", gAbsIncModal.format(90)), gCycleModal.format(81),
        getCommonCycle(x, y, z, cycle.retract),
        feedOutput.format(F)
      );
      break;
    case "counter-boring":
      if (P > 0) {
        writeBlock(
          (properties.type == "A") ? "" : gRetractModal.format(98), conditional(properties.type != "A", gAbsIncModal.format(90)), gCycleModal.format(82),
          getCommonCycle(x, y, z, cycle.retract),
          "P" + milliFormat.format(P),
          feedOutput.format(F)
        );
      } else {
        writeBlock(
          (properties.type == "A") ? "" : gRetractModal.format(98), conditional(properties.type != "A", gAbsIncModal.format(90)), gCycleModal.format(81),
          getCommonCycle(x, y, z, cycle.retract),
          feedOutput.format(F)
        );
      }
      break;
    case "chip-breaking":
      // cycle.accumulatedDepth is ignored
      if (P > 0) {
        expandCyclePoint(x, y, z);
      } else {
      //writeBlock(gCycleModal.format(74), rOutput.format(cycle.retract));
      writeBlock(gFormat.format(74), rOutput.format(cycle.chipBreakDistance));
      writeBlock(
        (properties.type == "A") ? "" : gRetractModal.format(98), conditional(properties.type != "A", gAbsIncModal.format(90)), gFormat.format(74), zOutput.format(z), peckOutput.format(cycle.incrementalDepth), feedOutput.format(F)
      );
      }
      break;
    case "deep-drilling":
      if (P > 0) {
        expandCyclePoint(x, y, z);
      } else {
        writeBlock(
          (properties.type == "A") ? "" : gRetractModal.format(98), conditional(properties.type != "A", gAbsIncModal.format(90)), gCycleModal.format(83),
          getCommonCycle(x, y, z, cycle.retract),
          peckOutput.format(cycle.incrementalDepth),
          // conditional(P > 0, "P" + milliFormat.format(P)),
          feedOutput.format(F)
        );
      }
      break;
    case "tapping":
      writeBlock(
        (properties.type == "A") ? "" : gRetractModal.format(98), conditional(properties.type != "A", gAbsIncModal.format(90)), gFormat.format(33),
                getCurrentCycle(x, y, z), feedOutput.format(tool.threadPitch)
        );
          writeBlock(mFormat.format(5));
          forceFeed();
          writeBlock(
              gFormat.format(33), zOutput.format(parseFloat(cycle.retract.toFixed(4))), feedOutput.format(tool.threadPitch), mFormat.format((tool.type == TOOL_TAP_LEFT_HAND) ? 3 : 4)
          );
          writeBlock(mFormat.format(5));
        break;
    case "left-tapping":
      F = tool.getThreadPitch() * rpmFormat.getResultingValue(spindleSpeed);
      if (properties.useRigidTapping != "no") {
        startSpindle(true, false);
      }
      writeBlock(
        (properties.type == "A") ? "" : gRetractModal.format(98), conditional(properties.type != "A", gAbsIncModal.format(90)), gCycleModal.format(74),
        getCommonCycle(x, y, z, cycle.retract),
        "P" + milliFormat.format(P),
        feedOutput.format(F)
      );
      break;
    case "right-tapping":
      F = tool.getThreadPitch() * rpmFormat.getResultingValue(spindleSpeed);
      if (properties.useRigidTapping != "no") {
        startSpindle(true, false);
      }
      writeBlock(
        (properties.type == "A") ? "" : gRetractModal.format(98), conditional(properties.type != "A", gAbsIncModal.format(90)), gCycleModal.format(84),
        getCommonCycle(x, y, z, cycle.retract),
        "P" + milliFormat.format(P),
        feedOutput.format(F)
      );
      break;
    case "tapping-with-chip-breaking":
    case "left-tapping-with-chip-breaking":
    case "right-tapping-with-chip-breaking":
      F = tool.getThreadPitch() * rpmFormat.getResultingValue(spindleSpeed);
      if (properties.useRigidTapping != "no") {
        startSpindle(true, false);
      }
      writeBlock(
        (properties.type == "A") ? "" : gRetractModal.format(98), conditional(properties.type != "A", gAbsIncModal.format(90)), gCycleModal.format((tool.type == TOOL_TAP_LEFT_HAND ? 74 : 84)),
        getCommonCycle(x, y, z, cycle.retract),
        "P" + milliFormat.format(P),
        peckOutput.format(cycle.incrementalDepth),
        feedOutput.format(F)
      );
      break;
    case "fine-boring":
      writeBlock(
        (properties.type == "A") ? "" : gRetractModal.format(98), conditional(properties.type != "A", gAbsIncModal.format(90)), gCycleModal.format(76),
        getCommonCycle(x, y, z, cycle.retract),
        "P" + milliFormat.format(P), // not optional
        "Q" + xFormat.format(cycle.shift),
        feedOutput.format(F)
      );
      break;
    case "reaming":
      if (P > 0) {
        writeBlock(
          (properties.type == "A") ? "" : gRetractModal.format(98), conditional(properties.type != "A", gAbsIncModal.format(90)), gCycleModal.format(89),
          getCommonCycle(x, y, z, cycle.retract),
          "P" + milliFormat.format(P),
          feedOutput.format(F)
        );
      } else {
        writeBlock(
          (properties.type == "A") ? "" : gRetractModal.format(98), conditional(properties.type != "A", gAbsIncModal.format(90)), gCycleModal.format(85),
          getCommonCycle(x, y, z, cycle.retract),
          feedOutput.format(F)
        );
      }
      break;
    case "stop-boring":
      if (P > 0) {
        expandCyclePoint(x, y, z);
      } else {
        writeBlock(
          (properties.type == "A") ? "" : gRetractModal.format(98), conditional(properties.type != "A", gAbsIncModal.format(90)), gCycleModal.format(86),
          getCommonCycle(x, y, z, cycle.retract),
          feedOutput.format(F)
        );
      }
      break;
    case "boring":
      if (P > 0) {
        writeBlock(
          (properties.type == "A") ? "" : gRetractModal.format(98), conditional(properties.type != "A", gAbsIncModal.format(90)), gCycleModal.format(89),
          getCommonCycle(x, y, z, cycle.retract),
          "P" + milliFormat.format(P), // not optional
          feedOutput.format(F)
        );
      } else {
        writeBlock(
          (properties.type == "A") ? "" : gRetractModal.format(98), conditional(properties.type != "A", gAbsIncModal.format(90)), gCycleModal.format(85),
          getCommonCycle(x, y, z, cycle.retract),
          feedOutput.format(F)
        );
      }
      break;
    default:
      expandCyclePoint(x, y, z);
    }
  } else {
    if (cycleExpanded) {
      expandCyclePoint(x, y, z);
    } else {
      var _x = xOutput.format(x);
      var _y = yOutput.format(y);
      var _z = zOutput.format(z);
      if (!_x && !_y && !_z) {
        switch (gPlaneModal.getCurrent()) {
        case 17: // XY
          xOutput.reset(); // at least one axis is required
          _x = xOutput.format(x);
          break;
        case 18: // ZX
          zOutput.reset(); // at least one axis is required
          _z = zOutput.format(z);
          break;
        case 19: // YZ
          yOutput.reset(); // at least one axis is required
          _y = yOutput.format(y);
          break;
        }
      }
      writeBlock(_x, _y, _z);
    }
  }
}

function onCycleEnd() {
  if (!cycleExpanded) {
    switch (cycleType) {
    case "thread-turning":
      forceFeed();
      xOutput.reset();
      zOutput.reset();
      g92ROutput.reset();
      break;
    case "tapping":
      writeBlock(gFormat.format(0));
      break;
    default:
      writeBlock(gCycleModal.format(80));
      writeBlock(gFormat.format(0));
    }
  }
}

var currentCoolantMode = COOLANT_OFF;

function setCoolant(coolant) {
  if (coolant == currentCoolantMode) {
    return; // coolant is already active
  }

  var m = undefined;
  if (coolant == COOLANT_OFF) {
    writeBlock((currentCoolantMode == COOLANT_THROUGH_TOOL) ? getCode("COOLANT_THROUGH_TOOL_OFF") : getCode("COOLANT_OFF"));
    currentCoolantMode = COOLANT_OFF;
    return;
  }

  switch (coolant) {
  case COOLANT_FLOOD:
    m = getCode("COOLANT_FLOOD_ON");
    break;
  case COOLANT_THROUGH_TOOL:
    m = getCode("COOLANT_THROUGH_TOOL_ON");
    break;
  default:
    onUnsupportedCoolant(coolant);
    m = getCode("COOLANT_OFF");
  }
  
  if (m) {
    writeBlock(m);
    currentCoolantMode = coolant;
  }
}

function onSpindleSpeed(spindleSpeed) {
  if (rpmFormat.areDifferent(spindleSpeed, sOutput.getCurrent())) {
    writeBlock(sOutput.format(spindleSpeed));
  }
}

function startSpindle(tappingMode, forceRPMMode, initialPosition) {
  var spindleDir;
  var _spindleSpeed;
  var spindleMode;
  var maxSpeed = "";
  gSpindleModeModal.reset();
  gSpindleModeModal.reset();

  if ((getSpindle() == SPINDLE_SECONDARY) && !gotSecondarySpindle) {
    error(localize("Secondary spindle is not available."));
    return;
  }
 
  if (tappingMode) {
    writeBlock(mFormat.format(29), sOutput.format(spindleSpeed));
    return;
  } else {
    if (getSpindle() == SPINDLE_SECONDARY) {
      spindleDir = tool.clockwise ? getCode("START_SUB_SPINDLE_CW") : getCode("START_SUB_SPINDLE_CCW");
    } else {
      spindleDir = tool.clockwise ? getCode("START_MAIN_SPINDLE_CW") : getCode("START_MAIN_SPINDLE_CCW");
    }
  }

  var maximumSpindleSpeed = (tool.maximumSpindleSpeed > 0) ? Math.min(tool.maximumSpindleSpeed, properties.maximumSpindleSpeed) : properties.maximumSpindleSpeed;
  if (tool.getSpindleMode() == SPINDLE_CONSTANT_SURFACE_SPEED) {
    _spindleSpeed = tool.surfaceSpeed * ((unit == MM) ? 1/1000.0 : 1/12.0);
    if (forceRPMMode) { // RPM mode is forced until move to initial position
      if (xFormat.getResultingValue(initialPosition.x) == 0) {
        _spindleSpeed = maximumSpindleSpeed;
      } else {
        _spindleSpeed = Math.min((_spindleSpeed * ((unit == MM) ? 1000.0 : 12.0) / (Math.PI*Math.abs(initialPosition.x*2))), maximumSpindleSpeed);
      }
      spindleMode = getCode("CONSTANT_SURFACE_SPEED_OFF");
    } else {
      if (properties.type == "A") {
        writeBlock(gFormat.format(50), sOutput.format(maximumSpindleSpeed));
      } else {
        writeBlock(gFormat.format(92), sOutput.format(maximumSpindleSpeed));
      }
      spindleMode = getCode("CONSTANT_SURFACE_SPEED_ON");
    }
  } else {
    _spindleSpeed = spindleSpeed;
    spindleMode = getCode("CONSTANT_SURFACE_SPEED_OFF");
  }

  // gear change
  if (properties.gearChange) {
       if ((_spindleSpeed > properties.gearLow) && (_spindleSpeed < properties.gearMed)) {
            writeBlock(mFormat.format(11));
        } else if ((_spindleSpeed > properties.gearMed) && (_spindleSpeed < properties.gearHigh)) {
            writeBlock(mFormat.format(12));
        } else {
            writeBlock(mFormat.format(13));
        }
  }

  if (getSpindle(true) == SPINDLE_SECONDARY) {
    writeBlock(
      spindleMode,
      sOutput.format(_spindleSpeed),
      spindleDir
    );
  } else {
    writeBlock(
      spindleMode,
      sOutput.format(_spindleSpeed),
      spindleDir
    );
  }
  // wait for spindle here if required
}

function onCommand(command) {
  switch (command) {
  case COMMAND_COOLANT_OFF:
    setCoolant(COOLANT_OFF);
    return;
  case COMMAND_COOLANT_ON:
    setCoolant(COOLANT_FLOOD);
    return;
  case COMMAND_LOCK_MULTI_AXIS:
    return;
  case COMMAND_UNLOCK_MULTI_AXIS:
    return;
  case COMMAND_START_CHIP_TRANSPORT:
    // getCode("START_CHIP_TRANSPORT");
    return;
  case COMMAND_STOP_CHIP_TRANSPORT:
    // getCode("STOP_CHIP_TRANSPORT");
    return;
  case COMMAND_BREAK_CONTROL:
    return;
  case COMMAND_TOOL_MEASURE:
    return;
  case COMMAND_ACTIVATE_SPEED_FEED_SYNCHRONIZATION:
    return;
  case COMMAND_DEACTIVATE_SPEED_FEED_SYNCHRONIZATION:
    return;
  case COMMAND_STOP:
    writeBlock(mFormat.format(0));
    forceSpindleSpeed = true;
    return;
  case COMMAND_OPTIONAL_STOP:
    writeBlock(mFormat.format(1));
    break;
  case COMMAND_END:
    writeBlock(mFormat.format(2));
    break;
  case COMMAND_SPINDLE_CLOCKWISE:
    switch (currentSection.spindle) {
    case SPINDLE_PRIMARY:
      writeBlock(mFormat.format(3));
      break;
    case SPINDLE_SECONDARY:
      writeBlock(mFormat.format(143));
      break;
    }
    break;
  case COMMAND_SPINDLE_COUNTERCLOCKWISE:
    switch (currentSection.spindle) {
    case SPINDLE_PRIMARY:
      writeBlock(mFormat.format(4));
      break;
    case SPINDLE_SECONDARY:
      writeBlock(mFormat.format(144));
      break;
    }
    break;
  case COMMAND_START_SPINDLE:
    onCommand(tool.clockwise ? COMMAND_SPINDLE_CLOCKWISE : COMMAND_SPINDLE_COUNTERCLOCKWISE);
    return;
  case COMMAND_STOP_SPINDLE:
    switch (currentSection.spindle) {
    case SPINDLE_PRIMARY:
      writeBlock(mFormat.format(5));
      break;
    case SPINDLE_SECONDARY:
      writeBlock(mFormat.format(145));
      break;
    }
    break;
  case COMMAND_ORIENTATE_SPINDLE:
    if (getSpindle() == 0) {
      writeBlock(mFormat.format(19)); // use P or R to set angle (optional)
    } else {
      writeBlock(mFormat.format(119));
    }
    break;
  //case COMMAND_CLAMP: // TAG: add support for clamping
  //case COMMAND_UNCLAMP: // TAG: add support for clamping
  default:
    onUnsupportedCommand(command);
  }
}

function engagePartCatcher(engage) {
  if (engage) {
    // catch part here
    writeBlock(getCode("PART_CATCHER_ON"), formatComment(localize("PART CATCHER ON")));
  } else {
    onCommand(COMMAND_COOLANT_OFF);
    writeBlock(gFormat.format(28), gMotionModal.format(0), "U" + xFormat.format(properties.g53HomePositionX)); // retract
    writeBlock(gFormat.format(28), gMotionModal.format(0), "W" + zFormat.format(properties.g53HomePositionZ)); // retract
    writeBlock(getCode("PART_CATCHER_OFF"), formatComment(localize("PART CATCHER OFF")));
    forceXYZ();
  }
}

function onSectionEnd() {

  // cancel SFM mode to preserve spindle speed
  if (tool.getSpindleMode() == SPINDLE_CONSTANT_SURFACE_SPEED) {
    startSpindle(false, true, getFramePosition(currentSection.getFinalPosition()));
  }

  if (currentSection.partCatcher) {
    engagePartCatcher(false);
  }

  forceAny();
}

function onClose() {
  writeln("");

  if (properties.barPullerEnable) {
    var workpiece = getWorkpiece();
    var stockDiameter = (workpiece.upper.x - workpiece.lower.x);
    var stockLength = (workpiece.upper.z - workpiece.lower.z);
    var pullAmount = stockLength;
    var pullFromLocation = stockLength + properties.barPullerEngagement;

    // Define EZ-Puller
    var pivotDistance = 0.875;
    var armLength = 1.25;
    var rollDiameter = 1.062;
    var zeroOrigin = 1.2444; //Resting roll separation distance 0.05.

    // Solve right triangle
    var sideC = armLength;
    var sideB = ((rollDiameter-pivotDistance+stockDiameter)/2);
    var sideA = Math.sqrt(Math.pow(sideC,2)-Math.pow(sideB,2));

    // Solve PullerOffset as negative radius value
    var PullerOffset = ((zeroOrigin-sideA)*-1); 

    writeComment("(Bar Pull)");
    if (properties.atcXZ) {
       writeBlock(gFormat.format(28), "U" + xFormat.format(0), "W" + zFormat.format(0)); // retract
    } else {
       writeBlock(gFormat.format(28), "U" + xFormat.format(0)); // retract
    }
    writeBlock(mFormat.format(1));
    writeBlock(mFormat.format(9));
    writeBlock(mFormat.format(5));
    writeBlock("G65H02P#502Q#502R1"); // add one to part count
    writeBlock("G65H85P02Q#502R#501"); // if completed skip pull and go to line 2
    writeBlock("T" + ("0" + properties.barPullerToolNumber).slice(-2) + ("0" + properties.barPullerToolOffset).slice(-2));
    writeBlock("G0Z" + zFormat.format(pullFromLocation * -1));
    writeBlock("X" + xFormat.format(PullerOffset));
    writeBlock(mFormat.format(52));
    writeBlock("G4P1500");
    writeBlock("G0W" + zFormat.format(pullAmount));
    writeBlock(mFormat.format(51));
    writeBlock("G4P1500");
    if (properties.atcXZ) {
       writeBlock(gFormat.format(28), "U" + xFormat.format(0)); // retract
       writeBlock(gFormat.format(28), "W" + zFormat.format(0)); // retract
    } else {
       writeBlock(gFormat.format(28), "U" + xFormat.format(0)); // retract
    }    
    writeBlock("G65H80P01");
    writeBlock("N02");
  }

  optionalSection = false;

  onCommand(COMMAND_COOLANT_OFF);
  
  onCommand(COMMAND_STOP_CHIP_TRANSPORT);

  // we might want to retract in Z before X
  // writeBlock(gFormat.format(28), "U" + xFormat.format(0)); // retract

  forceXYZ();
  if (!machineConfiguration.hasHomePositionX() && !machineConfiguration.hasHomePositionY()) {
    writeBlock(gFormat.format(28), "U" + xFormat.format(0), conditional(yOutput.isEnabled(), "V" + yFormat.format(0)), "W" + zFormat.format(0)); // return to home
  } else {
    var homeX;
    if (machineConfiguration.hasHomePositionX()) {
      homeX = xOutput.format(machineConfiguration.getHomePositionX());
    }
    var homeY;
    if (yOutput.isEnabled() && machineConfiguration.hasHomePositionY()) {
      homeY = yOutput.format(machineConfiguration.getHomePositionY());
    }
    if (properties.type == "A") {
      writeBlock(gFormat.format(53), gMotionModal.format(0), homeX, homeY, zOutput.format(machineConfiguration.getRetractPlane()));
    } else {
      //writeBlock(gAbsIncModal.format(90), gFormat.format(53), gMotionModal.format(0), homeX, homeY, zOutput.format(machineConfiguration.getRetractPlane()));
      writeBlock(gFormat.format(28), "U" + xFormat.format(0), conditional(yOutput.isEnabled(), "V" + yFormat.format(0)), "W" + zFormat.format(0)); // return to home
    }
  }

  onImpliedCommand(COMMAND_END);
  onImpliedCommand(COMMAND_STOP_SPINDLE);
  writeBlock(mFormat.format(30)); // stop program, spindle stop, coolant off
  writeln("%");
}